Nadcap Accredited for Chemical Processing

Approvals

Contact: Todd Webster, Quality Manager

1020 E Columbia Street • Weatherford, TX 76086, USA

Phone: (817) 594-5464, ext. 415 • Fax: (817)594-7450

E-mail: todd@weatherfordaerospace.com

Nadcap Accredited--Nondestructive Testing

 

Click on the company name below to jump to that section of the Approvals list.

Downloadable and printable versions of this page.
Click here: MS Word for a Microsoft Word-compatible file or here: PDF for an Adobe Reader version.




1. BELL HELICOPTER TEXTRON  #186692

Class 1Classified Parts Approved
QPS 100101 Quality System
PRIApproved for Primary Parts
CERTApproved for Critical and Primary Parts
FLTApproved for Flight Safety, Critical and Primary parts
BPS 4089Fluorescent Penetrant Inspection
IB1Machined Parts (Water Washable)
IB2Machined Parts (Post-Emulsified)
IB3Castings, including IB1 (Water Washable)
IB4Castings/Forgings, including IB2 (Post-Emulified)
BPS 4182QB1Chemical Film of Aluminum, Class 1A
BPS 4389Chemical Milling
QE1Aluminum
QE3Stainless and High Alloy Steel
QE5Titanium
QE6Forgings
QE7Pre-Penetrant Etch of Titanium
QE9Pre Penetrant Etch Titanium
SASheet Metal Assemblies (Complex)
SBSheet Metal Assemblies (Simple)
SCSheet Metal Details
BPS 4453IH1Inspection, Conductivity of Wrought Aluminum Alloys to Determine Heat Treat Conditions
PRIApproved for Primary Parts
BPS 4462Forming Titanium Sheet
SN1Cold Form
SN2Hot Form
SN4Cleaning and Descaling of Titanium Material to Section1
SORoll Forming
ZAMiscellaneous

RESTRICTIONS/COMMENTS:
Code ZA approval is restricted to fill and drain of cross and skid tubes per B/P requirements

  Back up to the Index Back Up to the Table of Contents

2. BOEING  #640761—Plant 1 / #550503—Plant 2

Class A Subcontractors
MIL-A-8625Chromic Acid Anodize Type I
BAC 5019Chromic Acid Anodizing - Classes 1, 3 and 5
DPS 11.01Chromic Acid Anodize
DPS 11.01-3Chromic Acid anodize, Chromate Sealed
PS 13201Anodizing of Aluminum Alloys
MIL-C-5541Chemical Conversion Coating, Immersion Applicaton Only (DIV X Exempt)
BAC 5719Chemical Conversion Coating for Aluminum, Immersion Application Only
BAC 5793Application of Corrosion Resistant Finish for Integral Fuel Tanks
DPS 4.50-127Fuel Tank Coating
ASTM-E-1417Penetrant Inspection
BSS 7039Liquid Penetrant Inspection
BAC 5423Penetrant Inspection
DPS 4.707Penetrant Inspection
PS 13201Anodizing Aluminum
BAC 5772Chemical Milling of Aluminum, Type 1 and Type 2
BAC 5842Chemical Milling of Titanium Alloys
DPS 9.481Chemical Milling of Aluminum
DPS 9.483Chemical Milling of Titanium Alloys
DPS 9.484Chemical Milling of Corrosion Resistant Steel
PS 20022Chemical Milling
PS 20650.3Chemical Blanking of Steel
HP 18-4Chemical Milling Limited to Type 2
BAC 5753Cleaning and Descaling of Titanium, Method II Only
Chemical Testing Process Solution Control, In House Support Only
ASTM-B-117Salt Spray Testing, WAI Only

  Back up to the Index Back Up to the Table of Contents

3. BOMBARDIER  #0000107525

Class A Subcontractors
BAPS 186Chemical Milling of Aluminum
BAPS 186-03Chemical Milling of Titanium and Titanium Alloys
PPS 42.01Chemical Milling of Aluminum and Aluminum Alloys
MPS 176-02Flourescent Penetrant Inspection
BAPS 138-43Application of Fluid Resistant Epoxy Primer, Limited to Curing in Paint booth Only
MPS 180-1Alkaline Cleaning
BAPS 180-30Alkaline Etching of Aluminum Alloys
MPS 180-31Cleaning and Deox of Corrosion and Heat Resistant Alloys and Titanium Alloys
MPS 180-32Acid Cleaning and Deox of Aluminum Alloys
CTS-0002-1BChemical Testing; Treatment Solutions and Waters
CTS-0002-5ACorrosion Testing

  Back up to the Index Back Up to the Table of Contents

4. CESSNA  #953511

CSMP 044Chemical Milling of Metals
CSFS 027Chemical Film, Chromate Conversion Coatings for Aluminum and Aluminum Alloys
CSFS 035Chemical Cleaning of Metals
CSFS 039Solvent Cleaning-Liquid
CSFS 084Coatings, VOC Compliant, Application
CSFS 007Application of Organic Coatings
CSFS 040Paint Stripping
CSTI 008Electrical Conductivity Testing
CSTI 028Hardness Testing of Metals

  Back up to the Index Back Up to the Table of Contents

5. GULFSTREAM AEROSPACE  #18640

ASTM-B-117Material Test-Salt Spray
GAMPS 3103Finish Paint, Topcoat and Primers
      3104
      3105
      3115
      3116
      3205
GAMPS 3102-7Finish Paint Protective Coatings
GAMPS 2701Chemical Milling of Aluminum
GAMPS 2702Chemical Milling of Steel
GAMPS 6201 / MIL-C-8625Chromic Anodize, Type 1
MIL-C-5541Conversion Coat of Aluminum, Class 1 & 3
MIL-STD-6866 / ASTM -E-1417Fluorescent Penetrant Inspection

  Back up to the Index Back Up to the Table of Contents

6. KAMAN  #232544-00

McDonnell Douglas Approved
QIP 06-02ADIR Supplier
MIL-I-45208Inspection System
KPS 228/MIL-C-81769Chemical Milling
GSS 9030 / MIL-A-8625Finishing-Anodizing-Chromic, Type 1
GSS 9010 / MIL-C-5541Finishing-Conversion Coat
KPS 950 / MIL-P-85582Epoxy Primer
GSS 4310Paint and Finish-Primers
GSS 4401 / MIL-F-18264Paint and Finish-Enamels
GSS 4402 / MIL-L-19537 / 19538Paint and Finish - Acrylics
GSS 4501Paint and Finish-Epoxy
MIL-C-85285Painting, Type 1
G-102 / MIL-P-23377Epoxy Primer-High Solids

  Back up to the Index Back Up to the Table of Contents

7. LOCKHEED MARTIN  EXP: #006055 & 192965

QCS-001Control of Process
FPS 1051Aluminum Chemical Milling
FPS 1051Titanium Chemical Milling
NDTS 1500 / 1501Hardness Testing
NDTS 1500 / 1502Conductivity Testing
NDTS 1101Penetrant Inspection - Zone 1A Fracture Critical Penetrant Inspection Approved, No Zone 1B or 1C
MIL-A-8625Chromic Anodize, Type 1 and 1B
MIL-DTL-5541Chemical Conversion Coating Type 1 Chem Film
FPS 3035Seal Bond Primer Application, Limited to Form 2 Primer
MIL-F-18264Prime and Paint
5PTPAG51Chemical Milling Aluminum, Ferrous, and Titanium, limited to P/N/ 5HF42418-107 and 5HF41410-109 (113) for LAI only
5PTPTT02-DFracture / Durability Critical Parts
5PTPTT11-AMission / Safety & Selected Durability Mech. Equipment
5PTPTT12-BWind Swept Surface Parts

  Back up to the Index Back Up to the Table of Contents

8. NORTHROP GRUMMAN / VOUGHT  #864280

GT23AFluorescent Penetrant Inspection
ASTM-E-1417Liquid Penetrant Inspection
GP17GPre-Penetrant Etching
AMS-C-81769Metals, Chemical Milling of; Limited to Aluminum and Titanium only
MA-63Chemical Milling of Aluminum
GSS 26100Chemical Milling of Aluminum Alloys
GSS 26300Chemical Milling of Titanium and Titanium Alloys
ASTM-B-177Standard Practice for Operating Salt Spray (Fog) Apparatus
MIL-DTL-5541Chemical Conversion Coatings for Aluminum and Aluminum Alloys
MIL-A-8625Anodic Coatings for Aluminum and Aluminum Alloys
GSS 5300Forming and Straightening of Aluminum Alloys, Limited to Cold Forming
GSS 4310Application of Epoxy Polyamide Primer

  Back up to the Index Back Up to the Table of Contents

9. VOUGHT AIRCRAFT INDUSTRIES  #864280

Preferred Performer Program Supplier (P3)
208-2-5Chemical Milling of Aluminum
STP51-402Chemical Milling of Aluminum Alloys, Limited to C-5 items only
VSS 26100Chemical Milling of Aluminum
GAMPS 2701Chemical Milling of Aluminum
VSS 26201Chemical Milling of Steel
VSS 26300Chemical Milling of Titanium
208-4-3Chemical Milling of Titanium
CVA 13-558Chemical Milling of Steel and Aluminum
MIL-C-81769Chemical Milling of Steel, Aluminum and Titanium
GAMPS 6201Anodize — Chromic Acid — 40v
CVA 9-4Anodize — Chromic Acid — 20 +/-2V
MIL-A-8625Anodize — Chromic Acid, Type 1A and 1B
80-T-35-1101 (PFA173)Airbus DA Chromating of Aluminum/Aluminum Alloys
208-9-100Cleaning and Etching of Aluminum
GP17GCleaning and Etching of Aluminum
VSS 7015Cleaning of Titanium
208-4-5Cleaning of Titanium
CVA 4-165Cleaning of Titanium
MIL-C-5541Chemical Film for Aluminum, Class 1A and 3
208-9-64Chemical Film — Colored for Aluminum Alloy
ASTM-E-1417Fluorescent Penetrant Inspection
GT23AFluorescent Penetrant Inspection
MIL-I-6866Fluorescent Penetrant Inspection
MIL-STD-6866Fluorescent Penetrant Inspection
208-14-11Fluorescent Penetrant Inspection
208-14-13Fluorescent Penetrant Inspection, Class A & AA
208-14-13Fluorescent Penetrant Inspection, Class B

  Back up to the Index Back Up to the Table of Contents

10. EMBRAER   

NE 40-012 ABMetallic Parts — Cleaning
NE 40-030 PAluminum and Its Alloys — Anodic Coatings in Chromic Acid
NE 07-001 JLiquid Penetrant Inspection
NE 40-159 GHigh Solids Epoxy Primer (MEP10-068) for Exterior Metallic Parts — Application Requirements
NE 40-160 NHigh Solids Polyurethane and Metallic (MICA) Enamel (MEP 10-069) — Application Requirements

  Back up to the Index Back Up to the Table of Contents

11. VIKING   

VPS 42.01Chemical Milling of Aluminum Alloys

  Back up to the Index Back Up to the Table of Contents

12. BF GOODRICH   

MIL-A-8625Chemical Milling of Aluminum Alloys
QA-111Section 2
RPS 14.06Chemical Milling of Aluminum Alloys

  Back up to the Index Back Up to the Table of Contents